KT200 ECU Programmer Support OBD/BOOT/BDM/JTAG Multiple Protocols
KT200 ECU programmer supports ECU maintenance chip tuning, DTC code removal, OBD/BOOT/BDM/JTAG, and multiple protocols. The hardware of the KT200 ECU programmer is the Master version.
Free Download KT200 Software on www.ktmtool.com
New KT200 KTsuite Driver List: https://www.ktmtool.com/driverlist.html
CAN NOT SUPPORT OFFLINE DONGLE
Master: Read and write ECU data, read it in BIN unencrypted format, you can modify the data arbitrarily, you can clone ECU and use it as ECU service, the master is a personal version, you can only use it yourself, cannot unlock data for the slave.
Works online only. CAN NOT SUPPORT OFFLINE DONGLE
It runs via KTSuite Manager program. Software requires activation before use (Check activation instructions on the bottom of the page).
Supported Winols damaos supply
As we all know,winols damaos and A2L is very expensive,we supply these to ours customer as free, so you can get it for chitpuning , dtc off, and so on
KT200 Operation Mode
1：OBD mode：(read the data from Diagnostic port ,you need remove the ecu or tcu from car or open the ecu box , just read everything from car, we also support obd vr read, we supply original file from our server, you can direct obd vr read it )
2: BENCH mode: we also call it service mode, you can use this mode clone or backup all ecu data, read the internal flash and external flash and eeprom data, so you can save a lot of money for clone ecu and tcu , you also can clone tcu and chiptuning with this mode.
3: Jtag mode: open the ecu , and wire it or use ours adapter connect ecu ways,some of denso ecu always need use this mode for read and write .
4: Boot mode: open the ecu and always can backup everything , read the flash and eeprom , you can save some ecu cause your obd write failed, or some others reason cause the ecu dead.
5: BDM mode: some of the ecu need read and write in bdm mode ,open the ecu and use ours adapter connect it
KT200 Supported Functions
Adblue and SCR off
gearbox data to adjust LC
HOT Start Fix
Flaps / Swirl Removal
Sport Displays Calibration
Cold Start Noise Reduction
Speed Limiter Removal
Torque Monitoring Disable
Exhaust Flap Removal
OBD Reading Protection
Boost Sensor Calibration
LC, AL and NLS for MED9.1
vmax, swirl off
restoring ECU or TCU factory setting service
VIN fix (EEPROM support checksum , so you can easy change VIN then write back )
1pc x Master machine
1pc x KT200bench box
1pc x USB cable
1pc x Power adapter
1pc x Fox box store over 10 adpaters
1pc x Jtag and bdm cables
1pc x Pen
1pc x Notebook
1pc x Carton case
1pc x Function cable for boot, bench, kline links .
1pc x Truck OBD cable
1pc x Car OBD cable
1pc x Paper box
1pc x Install guide
1pc x Main software
1pc x Technical Support
1pc x Login account for software and tools
1pc x PDF pacakges for connecting ecu and tcu
1pc x Join facebook group for support
1pc x Online chat support for use
Extra pacakge according to users request after the user get the tool.
1pc x Tuner account
1pc x Helpdesk
1pc x WinOLS damaos, A2L
How to Activate KT200 KTsuit Manager Software?
Do follows work before start our tools
A:Connect your KTsuit with USB cable to laptop
B:laptop or PC must connect to internet
Step 1: go to www.ktmtool.com website donwload the software KTSuit,install the package.
Step 2: Check the SN where tie on your box backside , noticy : dont realase that SN to anyone , its a safe code for you ,dont let any third party or guys know that code or it easy let your tools lock.
Step 3: Send that SN to email:[email protected] for active and link your tool to your email .(you tool will be lock if you dont send to active)
Step 4: Run the ktsuit manager, and register it with your email , then input the sn active your account, don’t close the ktsuitmanager before your run ktsuit ,always keep click the active button before you run the ktsuit software.
Step 5: input that SN code to you login windows when you run KTsuit main software, it will ask you input that code ,then you software and tool will be online.
How to Run KT200 KTSuit?
1 Shutdown date and time automatically sync
2: Shutdown defender
3: Shutdown antivirus system
4: Run kt suit manager click Active button
5: Keep KTSuit manager run
6: run kt suit
The following models can be read and programmed:
5.Additional TCU package available for Automatic Transmissions.
The cover-free method can read and write the following protocols through PIN OUT:
(Unlocking also possible via pinout)
System-wide via PIN OUT (MICRO/FLASH+EEPROM) the following ECUs:
JTAG NEXUS MPC/SPC56xx
JTAG NEXUS MPC55xx
-BOOT MODE ST K-LINE/RX-TX/CAN
-BOOT MODE Tricore for micro
-BOOT MODE Renesas
-BOOT MODE Mitsubishi
-BOOT BAM SYSTEM MOTOROLA
-BOOT MODE Fujitsu
-BOOT MODE Hitachi
ADDITIONAL PACKAGE FOR AUTOMATIC TRANSMISSION
FULL READ AND WRITE TCU(MICRO+EEPROM)
TCU CODING FUNCTIONS
Multiple connection possibilities:
KT200 software display:
Here Gm-Tech2.com engineer collects some common errors and solutions of KT200 ECU Programmer full and basic version.
Problem 1: Software cannot connect to the server
After connect KT200 device, click on “CONNECT”, it says “WAIT INTERNET CONNECTION” but it has not been connected. Error!!! Send Log File to support.
Disable Windows Defender.
Take the computer WIN10 system as an example, open the windows settings：
Search and open “Virus and Threat Protection”, check whether anti-virus protection software is installed, and close and delete the anti-virus software if so
In windows settings, search for “firewall and network protection” settings and turn off network firewall.
And check if Windows Defender Firewall is turned off synchronously.
Make sure you have closed the firewall and anti-virus system software, reopen KT200, and connect to the server.
Problem 2: Diagnose detect problem
In the KT200-master folder, the suffix dll files cannot exceed three letters, and the extra ones can be deleted.
There are three files Gcheck.dll, SecurityAccess.dll, wuzi.dll in the folder
Problem 3: Time zone problem
If the time zone is inconsistent with the current location, KT200 will display an error Computer clock is wrong.
In the computer settings, search for “time”, select the corresponding time zone, and synchronize the network time.
Problem 4: Driver problem can’t open
The driver is missing, error Cannot load file libcrypto-3.dll Error: 126
Install the patch package corresponding to the operating system, and it can run normally
The 32-bit system corresponds to the X86 version, and the 64-bit system corresponds to the X64 version.
Problem 5: dfb2xx.dll file error
Use Diagnose to detect, displays an error Wrong size or version of C/windows/syswow64/dfb2xx.dll
This is because the size of the dfb2xx.dll file in C:\windows\syswow64 is inconsistent. The size of the dfb2xx.dll file of KT200 is 202kb, not 392kb, so replace it.
Problem 6: Driver error. Driver is wrong.
When opening the software, it prompts that the driver is wrong，
Open the computer settings, search for “recovery”, select “reset this computer”
Then select “Troubleshoot”
select “Advanced Options”
Select “Startup Settings”
Finally, just select “Disable automatic driver signing”.